Skip to content

Mediazione Creditizia — OAM 2014-A

AQL sampling plan for final random inspection (fri): what importers book before shipment: part 2

The short answer

Before booking final random inspection, write the sampling plan down: define the lot, fix the sample size, classify defects, and set the accept and reject numbers. That short document decides whether the visit produces a defensible ship-or-hold decision or just a stack of photos. Everything below shows how importers phrase each line.

Key takeaways

  1. An AQL plan fixes the lot, the sample size, the defect classes, and the accept and reject numbers before the inspector arrives.
  2. Random carton selection from the full packed lot is what makes the sample representative of the shipment [1].
  3. Critical, major, and minor defects normally carry different acceptance limits within the same visit.
  4. Factory acceptance logic treats the inspection as a shipment decision gate, not a sorting exercise [2].
  5. The booking note should state lot size, inspection level, AQL per class, and what happens on failure.

Most failed shipments do not fail because the inspector was careless. They fail because nobody wrote down what the sampling plan was supposed to prove. The factory thought the visit was a quick look at a few cartons, the buyer thought it was a full acceptance decision, and the report landed somewhere in between. A written sampling plan removes that ambiguity before anyone opens a box.

An AQL sampling plan answers four questions in advance: which goods count as the lot, how many units get drawn, what counts as a defect, and how many defects flip the verdict from pass to fail. Acceptance sampling is a statistical compromise, not a full sort; its logic only works when the lot is defined, the draw is random, and the acceptance numbers are fixed before inspection starts. Guessing any of these on the day invites argument.

This second part of the series focuses on the booking itself: the exact lines an importer puts into the inspection request so the visit matches the purchase order. It assumes the reader already knows the basics of final random inspection and wants a practical template for lot definition, level selection, defect classes, and pass-fail arithmetic.

What the sampling plan must fix in advance

A sampling plan is a contract about evidence. It states the lot size in units and packed cartons, the inspection level that determines the sample-size code letter, and the acceptance quality limit for each defect class. Once those three inputs are fixed, the sample size and the accept and reject numbers follow from the standard single-sampling tables, and nobody needs to negotiate them on the factory floor.

Acceptance sampling exists because checking every unit of a large shipment is rarely practical; a properly drawn sample lets the buyer make a lot-level decision with a known and bounded risk [1]. That logic collapses if the lot changes mid-visit, so the plan should name the purchase order lines covered, the cartons that belong to the lot, and anything excluded, such as goods still on the production line. Anything produced after the draw is a different lot with its own verdict.

Buyers sometimes confuse the sampling level with product quality. The level only sets how many units get checked relative to lot size; the AQL sets how strict the verdict is. A small lot at a special level can pass with few defects found simply because little was examined, which is why the report should always print the lot size next to the sample size. Readers of the report need both numbers to judge what the verdict is worth.

Illustrative sample sizes at general level II

Lot size (units)Sample size codeUnits inspectedWhat it tells the buyer
91 to 150F20A light check suited to small repeat lots with a stable supplier
281 to 500H50A mid-size draw where one major defect already matters
1,201 to 3,200K125A standard container-lot draw with meaningful discrimination
10,001 to 35,000L200A full-container draw where sampling risk is well bounded
35,001 to 150,000M315A large-program draw, usually split across several working tables
Illustration: Illustrative sample sizes at Decorative illustration for the section "Illustrative sample sizes at"; visual only, carries no data.

Classify defects before quoting any AQL number

Classification has to happen product by product, because the same flaw can be minor on one item and major on another. A shade variation is minor on a work glove and major on a fashion garment sold as a matched set. The booking should attach the defect list from the purchase order or the approved golden sample notes, with photos where wording alone could be read two ways.

Critical defects

A critical defect makes the product unsafe or unusable, or breaks a regulatory requirement: exposed mains wiring, a failed insulation barrier, a sharp edge on a child product. Most buyers set the effective limit at zero, meaning any confirmed critical defect fails the lot regardless of what the sample arithmetic says. The inspector needs this rule in writing, because stopping a shipment over a single unit takes authority.

Major and minor defects

A major defect impairs function or marketability: a dead button, a wrong voltage label, a seam that opens under normal load. A minor defect is cosmetic and does not affect use: a light scuff inside the packaging, a slightly uneven print. Typical bookings pair a tighter AQL for majors with a looser one for minors, for example 2.5 for major defects and 4.0 for minor defects on general consumer goods. The exact numbers matter less than the fact that both sides agreed them before the first carton was opened.

Write the booking note the inspector can execute

See the inspection scope. Then confirm the lot size, the finished and packed carton count, the sampling level, the AQL per defect class, and the carton-selection method in the same message so the inspector arrives with one written plan. A booking that contains all five lines rarely produces disputes, because the factory heard the same instructions the buyer sent.

Illustration: Write the booking note the Decorative illustration for the section "Write the booking note the"; visual only, carries no data.

Name the decision rule for each outcome while booking, not after the failure photos arrive. State who gets called when the lot fails, whether sorting under supervision is acceptable, and whether a re-inspection draws a fresh sample or returns to the same cartons. Factory acceptance practice treats this visit as a gate between production and dispatch, and gates only work when the closed-gate procedure is written down [2].

Add the practical details that decide whether the plan survives contact with the warehouse: the inspection address, the contact person, the start time, the tools the inspector may need, and confirmation that packed cartons will be accessible for random pulling. A plan that ignores access usually ends with the inspector checking whatever was staged near the door. That is not a random sample, whatever the report header claims.

The most common failure mode is a lot that grows during the visit: cartons finished while the inspector works, or a second purchase order wheeled in and added to the count. The rule is simple and should be in the booking: units packed after sampling starts belong to the next lot. Enforcing it feels awkward on the day and saves the buyer from a verdict that covers goods nobody examined.

Sources

  1. Wikipedia: Acceptance sampling —— Overview of acceptance sampling including AQL concepts used in product inspection.
  2. Wikipedia: Factory acceptance test —— Overview of factory acceptance testing performed before shipment or installation.

Frequently asked questions

Can the factory preselect the cartons the inspector opens?

No. The plan is drawn from the production lot as packed cartons, never from cartons the factory preselects or stages separately. If the inspector cannot pull cartons at random from the full lot, the sampling math no longer represents the shipment, and acceptance-sampling references describe why random selection is the foundation of the method. Ask the factory to keep all packed cartons accessible until selection is done.

What changes when a buyer moves from general inspection level II to level III?

It means the inspector checks more units, which tightens the decision without changing the defect definitions. A tighter level is common for regulated or high-visibility goods, while a general level suits standard consumer products with a track record. The choice belongs in the written booking so the inspector and the factory work from the same numbers.

Can one shipment use different AQL values for critical, major, and minor defects?

Yes, and most experienced buyers do. Critical defects usually carry the tightest limit, often zero tolerance in practice, while major and minor defects carry progressively higher acceptance numbers. The classification section of the article shows how to assign failure modes to each class before quoting an AQL number.

What should the inspection report record about the sampling plan itself?

Record the lot size, the cartons produced versus packed, the sampling level, the AQL per defect class, and the acceptance and rejection counts actually found. Photograph the carton count, the sampling labels, and any failed units. This record lets the buyer, not the factory floor, decide whether the lot ships, gets sorted, or gets reworked.

Redazione CTM Italia

admin

Consulente del credito e analista del team editoriale di CTM Italia. Si occupa di normativa bancaria, mutui e tutela del consumatore creditizio.

Approfondimento
Mutui e Prestiti
Approfondimento
Credito alle Imprese
Approfondimento
La nostra Rete
Parliamone
Contatti

Pronto a confrontare la tua rata?

Oltre 1.200.000 preventivi erogati dal 2007. Compila il modulo e un consulente OAM ti ricontatterà entro 24 ore lavorative.

Richiedi un preventivo gratuito